AMPS jobs

...Experience: • Proficiency in electronic circuit design, specifically analog audio circuits. • Experience with handling multi-channel signals. • Familiarity with line level audio signal processing and mixing. We need an engineer with deep experience in high-end analog circuit design using low noise operational amplifiers. We will provide basic diagrams and objectives. The project involves high quality op amps and line drivers for an audio routing project. We will be using FPGA platforms with SPI and TCP/IP to send commands to digitally controlled audio daughterboards in a card cage configuration. The proof of concept will include circuit design and a functioning prototype of two audio channel for control and noise and sweep analysis of the output. We have pre-sele...

I'm in need of an experienced electrical engineer with expertise in power systems and circuit design. I'm looking to have a flyback converter developed that can meet the following specifications: - Input Voltage: 24 V DC - Output Voltage: 3 V - Load: 5 Ω - Output Current: 1-3 Amps - Load-Voltage Variation: < ± 3% The primary objectives of this project are to achieve a high level of efficiency and to ensure the device can deliver a consistent 3V to the 5 Ω load, while also being able to handle variations within the specified range. Ideal candidates for this project should possess: - Proven experience in designing flyback converters - Proficiency in power systems and circuit design - Ability to optimize for high efficiency - Experience in delivering stable volta...

I'm in need of an experienced engineer who has a solid background in measurement systems particularly using load cells and load cell amps and basic platform development. The objective is to develop a project which measures loads within a range of 10-20kg , with data input to an Arduino microcontroller. The ability to configure an edge device to continuously stream data to a simple BI dashboard on a desktop is also required. The successful freelancer should have the following skills and experience: - An excellent understanding of load cells and how to operate and interpret readings from them. - Extensive experience using Arduino microcontrollers and able to proficiently program and troubleshoot them. - Knowledge on how to integrate an edge device with this setup, and the skill...

I require the development of a Printed Circuit Board (PCB) based on provided schematics and design guidelin. This PCB is specifically designed to amplify signals from a silicon PIN diode used to sense gamma radiation. Top Features: A PIN photodiode, four low-noise op amps and a comparator are used to detect individual photons of gamma radiation. Expertise: - A solid background in PCB design and experience in providing PCB manufacturing data Expected output: • Schematic and Source data in EAGLE or Protel 98/99/SE/Altium/Protel-DXP format. • Extended Gerber File RS-274X. • Bill of Materials (BOM) in Excel format, based on components from Digikey or Mouser. • Pick-N-Place / XY-File. Please share relevant experience and sample work.

I am in need of an experienced PCB designer to create a highly durable printed circuit board that incorporates a TI INA229 current and voltage sensing IC, along with a PCB mounted shunt resistor capable of handling up to 50 amps. The board should be designed to withstand industrial use. Key Requirements: - Incorporating TI INA229 current and voltage sensing IC - Capable of handling up to 50 amps, 85V DC. - High durability for industrial use - All external connections to be via screw terminals (e.g. phoenix) and support the required current. - calculation of required parameters for INA229 register settings. - Size is flexible - Would be ideal if there was onboard 5V regulator for VIN of INA229, but open to this being external supply. Ideal Skills: - Strong background in PCB ...

I'm looking for a skilled logo designer who can create a vibrant logo for my electrical company. Essential elements needed are: 1) Name: Amps & Ohms Electrical 2) Needs to be instantly recognisable as an electrical company - light bulb / power volt etc 3) Logo style: Modern & Sleek Must work on both white and black backgrounds Submissions should reflect proficiency in color theory and visual composition. The selected designer would need to provide the final logo in both print and digital formats. The logo should be scalable and visually striking both in color and black and white.

I am looking for an experienced electrician to upgrade a 200 amps electric panel to a 400 amps panel at a commercial property. The upgrade is essential due to: - An increase in our energy needs. Specific equipment that will be connected to the new 400 amps panel: A new air compressor 220 1-phase 125 amps that elevates the total consumption to 315 amps The ideal freelancer for this project should have: - Experience with commercial property electrical systems. - Ability to handle high-capacity electric panel upgrades. _ Be able to draw the schematic diagram required for the SRP Your bid should include: - Materials and labor costs - Estimated timeline for completion . Your attention to detail will be critical in this project to ensure ene...

I need someone to return musical equipment, specifically two amplifiers weighing around 100 lbs, to Hoffman Music in Spokane. They are currently being held at the front desk in the DoubleTree hotel. No special handling or packaging is required. Since the amps are rather bulky, the ideal candidate should have ample car/truck storage space.

I am in need of an Electrical Engineer who has hands-on experience in designing bus bars for high current systems. I have a project that involves the creation of a copper bus bar capable of carrying 1000 Amps DC used to connect various electrical components. Key requirements include: - Bus Bar Material: The prime material for the bus bar should be copper due to its excellent conductivity. - Connective Capability: The bus bar's prime role is to serve as a conduit to connect different electrical devices. It must be expertly designed to efficiently distribute high voltage. - Heat Resistance: Given the high current passage, the bus bar should withstand high-temperature conditions without any compromise on performance and safety. I am keen on working with someone who can bring ...

I need a free...the shop, and still use all rooms. We want the kitchenette to be as functional as possible, with all the things a modern kitchen would have, fridge, stove, dishwasher, sink, microwave, air fryer, etc. We would like the loft area to have a ladder, or stairs that again, does not block the entry via main shop doors, but allows for a small bed, and computer desk and chair. There is a J box with 100 amps of power, so we will need a place for a sub panel for the room. There is a gas line there as well, and sewer and water are in the ground just on the other side of the shorter wall, so we will have to cut the concrete to install drains. We will need to go through multiple variations, and would like to start with a rough idea of layout, and once agreed upon, have it det...

I'm in need of a professional engineer who specializes in busbar designs for a power distribution system. This project primarily entails designing a copper busbar with a current carrying capacity of 500-1000 Amps, and ensuring efficient power distribution throughout the system. Key Skills And Experience: - Expertise in electrical engineering, specifically busbar design - Extensive experience with the use of copper in busbar design - Proven knowledge on power distribution protocols - Have previously designed systems with a similar current carrying capacity - Able to provide practical, cost-effective solutions. This project demands detail-oriented professionals who are able to meet timelines without compromising quality. An understanding of safety protocols is necessary, as it...

Please Sign Up or Login to see details.

I urgently need a skilled and experienced electrician to boost the size of my current electrical panel. It's a 150 amps panel for 10 apts, which I am looking to upgrade for increased capacity. The ideal capacity I'm aiming for is double the current one, turning it into a large-scale 400-amp system. Your expertise in similar projects that involve resizing electrical panels and configuring the circuits to accommodate the increased power demand is crucial for this job. Some key details of the project are: • Assessment of current panel and circuit layout • Replacing the 150-amp panel with a 400-amp one • Ensuring safety standards and protocols are followed • Regulating power supply to avoid system failure Remember, the goal is to increase the capacity of ...

I urgently need a skilled and experienced electrician to boost the size of my current electrical panel. It's a 150 amps panel for 10 apts, which I am looking to upgrade for increased capacity. The ideal capacity I'm aiming for is double the current one, turning it into a large-scale 400-amp system. Your expertise in similar projects that involve resizing electrical panels and configuring the circuits to accommodate the increased power demand is crucial for this job. Some key details of the project are: • Assessment of current panel and circuit layout • Replacing the 150-amp panel with a 400-amp one • Ensuring safety standards and protocols are followed • Regulating power supply to avoid system failure Remember, the goal is to increase the capacity of ...

I'm seeking a designer and proto-type builder to provide a comprehensive solution for my industrial control switch requirements. The intended environment is Indoor stationary and the switch will be handling a resistive load. Key requirements: • Design a control switch rated for 30 amps/ 110VAC. • The switch should incorporate a master on/off safety switch and a variable timer of 1-60 minutes. • There should be a provision for resettable and variable on-off cycle-counting switch. • The system should be capable of switching between two channels. Ideal Skills and Experience: • A strong background in electrical or electronics engineering. • Previous experience designing and prototyping industrial control switches. • Familiarity with resistive ...

We are in search of a skilled team capable of designing, programming, and integrating a set of four PCBs from the ground up, ready for immediate use. Our project includes: 1. An RF controller, 2. A main receiver computer coupled with a transmitter for motors, 3. A BLDC motor controller capable of handling 400 amps, and 4. A GPS board. The team must exhibit proficiency in: - Programming, - PCB design, - Bluetooth technology, - RF controllers, - App development. Included are the detailed circuit board requirements and two suggested microcontrollers for consideration, though we remain open to expert recommendations. We seek partners who can bring substantial experience to the table, particularly those who have previously completed successful PCB design and development projects. If...

We are looking for an Electrical Engineer with expertise in Automotive electrical work and testing equipment. We are looking to develop some equipment and need a highly qualified engineer to assist us. I am attaching some photos of the a/c compressor we are working on. We are looking for a EDT in High voltage brushless inverter 20 amps 3 poles

I'm seeking an expert to design and deliver a supplemental power solution for my food service needs. Here are the specifics: - **Capacity and Duration:** - Must supply 30 Amps of power - Ability to switch seamlessly from main power to supplemental for continuous service - **Voltage:** - Designed to operate at 220V An engineer suggested a power supply derived from basically a battery pack that’s between machines and mains to supplement power surge requirements when machine calls for the power, this then releases problems with overloads on circuit breaker boards Ideal skills and experience required: - Electrical engineering background - Experience with high-capacity batteries - Knowledge of food service industry power requirements - Ability to c...

I am in need of a seasoned electrician or electrical engineer with experience in residential multi-unit apartments. Job Details: - Specialty: Electrical panel upgrade, knowledge in relevant permit necessities - Specifics: Our current main panel is at 150 amps capacity and we hope to replace it completely. Your expertise is needed to progress to a 200 amps panel. - Deliverables: Detailed electrical drawings for permit approval. Your experience in carrying out similar tasks will be highly regarded. Having a comprehensive understanding of local codes and standards is vital. Excellent draftsmanship skills is also a requirement for this job. It's a great opportunity for someone who is meticulous, highly knowledgeable and can meet deadlines.

...tripping out on over current. I need an intermediate controller to boost the pair of existing pulse width modulating (PWM) 0-14VDC 5 amp signals (A and B per attached block diagram) from the car computer, into an identical PWM 0-14VDC but 15 amp current capacity (A' and B'). Your design (in green on the second block diagram) will ONLY have inputs from A and B, plus power and ground for 14 VDC at 15 amps. You will NOT have any access to other vehicle control systems whatsoever. Your design must replicate the same input PWM signals A and B exactly and instantly, just with more amperage, and output only A' and B'. I will need to review your schematic design, and will need a PCB design and bill of materials for fabrication. This is a simple design so my budg...

...an experienced professional to check / evaluate the design of an analog electronic circuit. What I need is a professional opinion of circuit design attached. The prototypes provided do not work at all, so I am wondering is it a design or implementation issue? The circuit meant to be a current limiter that would work up to 600V DC and up to 20amps and be able to limit current between 0 and 20 amps regardless the voltage, so with the utilization of a potential-meter the user could regulate the current . Specific Requirements: - Evaluate the overall design of the analog electronic circuit - Provide a high level overview of the circuit design Ideal Skills and Experience: - Extensive knowledge and experience in analog electronic circuit design - Strong understanding of electron...

Friction of rider bands and its Wear rate , and the effect on motors amps.

...air valve) uses two wires ETCSM+ and ETCSM- to position the actuator as shown in the attached circuit diagram. The existing motor is 2.85 ohms, and draws under 5 amps at 14 vdc. This actuator motor is being replaced with a much larger motor that draws up to 15 amps (1.35 ohms) for racing purposes, but the factory controller can only handle 5 amps before it cuts out. So I need an additional controller that takes the pair of factory positioning signals (0-14vdc each) at under 5 amps, and generates an identical set of positioning voltages to the larger actuator at up to 15 amps. A separate fused 14vdc power feed at up to 20 amps is available for the new controller to utilize. The actuator motor does not require speed modulation, but I do need...

...is flexible. Skills and experience required: - Strong knowledge and experience in circuit design - Ability to work with a rough idea and provide suggestions for layout design - Flexibility in terms of project completion timeframe Sine wave output voltage Output frequency 50 Hz EN 50155 compliant Input voltage 110 Vdc Input voltage range 77 - 138 Vdc Output voltage 230 Vac Output current 12.5 Amps Apparent output power 1500 VA Output voltage control with input 0-10 Vdc Open loop control is used. This inverter will be used to control a 1 kW fan mounted on the train, therefore the size of the inverter should be as small as possible. The design should be as cost effective as possible. It should be a reliable design with all protection such as overcurrent, shortcircuit etc. ...

i need simple electrical riser diagram for (200 amps with 3 phase) one panel inside and one outside... check the sample diagrams from other projects. this is for NEC (national electric code) the electrical pole outside is (overhead pole) to the building

Hi, I am a master electrician and owner of NexGen Electric. I have a project that will require drawings for ESA and Utility Company application. Client requires an upgraded service in order for the new machine that is coming in. My load demands have calculated 533 amps in total, so we need to upgrade to 600 amp (possibly 800 amp if client wants expansion). I can do all the leg work, I just require line diagrams and electrical room layout plans (I can even help design that).

I am looking for an experienced engineer to assist me with a project involving a simple analog mic circuit. I need to add an Op-Amp to increase the voltage by a factor of 10 for a simple microphone circuit. Input Voltage Range: The input voltage range for the mic circuit is 48VDC. Op-Amps Needed: Only one Op-Amp (AD743) is required for this circuit. Skills and Experience Required: - Strong knowledge and experience in analog circuit design. - Proficiency in using KiCad or TINA or Altium for circuit simulation and design - Ability to create a Bill of Materials (BOM) and create Gerber files. If you possess the necessary skills and experience, please submit your proposal for this project.

Mix and master my pop song - I want the vocals, instrumentals, and bass to be en...music projects. I am doing a challenge where I make a song a day for 30 days, so you could get a lot of work by winning this contest. Here's the mix that I did: Here's a link to the unmixed stems: Here's a link to the stems with amps and effect plugins (mostly the guitars and vocals are different): For some reason, freelancer doesn't give the option to put audio files as accepted formats. For me, I will accept .mp3 for the demos and .wav for the final file.

I have a rectifier with output 80 amps. Need a circuit for changing polarity of the output current

Cost effective and very accurate Voltmeter, Ammeter and Watt meter combined circuit, with 0-5Volt DC output to control Voltage and 0-5 Volt to control Current from a DC power supply. It has to be designed to show the parameters by an adequate graphical display. Two rotating encoders to be provided to control both volt...0-5Volt DC output to control Voltage and 0-5 Volt to control Current from a DC power supply. It has to be designed to show the parameters by an adequate graphical display. Two rotating encoders to be provided to control both voltages of 0-5 volt and the center switch within the encoder to be made toggle for the Coarse and Fine settings. Display resolution for voltage should be 00.00 Volt, 00.00 Amps and 4 digits to show Watt. An image is attached herewith for your re...

I am looking for a designer to make specific changes to our logo for a new division. The ideal candidate will have experience in logo design and be able to make color and wording changes while keeping the original style intact. Specific Changes Needed: - Color change - Wording change Color Scheme and Wording: - I will provide specific colors and words to use for the new logo Logo ...original style of the logo Skills and Experience Needed: - Proficiency in logo design - Ability to make color and wording changes - Attention to detail - Creative thinking - Ability to work within the constraints of the original logo design. Attached is my current logo. The other attachment is my competitors logo in which i would like my logo to have the same blue and red colours with the wording amps...

Looking to develop a board with below description: Hardware: 1. Control 4 motors of 10 amps load, with current sensing & PWM 2. Mesh network with zigbee 3. Battery management circuit 4. 2 sensors Firmware: 1. Sensing the motor currents , and give alarm if it’s overload 2. Get motor current data 3. Get battery voltage 4. Get sensor data 5. Mesh network with zigbee protocol 6. Bluetooth control

Logo/Brand Design for AMPS - AllMarine Power Solutions - Looking for a modern and sophisticated logo design for our Lithium Battery company - Open to both text and symbol logos, or a combination of both - Specific colors are preferred, so please incorporate them into the design - Ideal skills and experience for this project include: - Strong graphic design skills with a portfolio showcasing modern and sophisticated logo designs - Experience in creating logos for battery or technology companies - Ability to create a versatile logo that can be used across various platforms and sizes - Attention to detail and ability to understand and incorporate client preferences - Good communication skills to collaborate with the client and iterate on the design if needed Some designs I ...

Need to build a EMI filter requiring isolation from 100khz to 700 Mhz 5-50vdc 10 amps. I have a design in mind and have designed in spice but would like it refined to component's to use and spec's. Voltage loss needs to be minimized and heat production must be min. Would prefer to use one manufacture of components as much as possible.

...to design a circut board for a low voltage project. I do not have a schematic, so I am open for suggestions on the design. We are looking for a circut board design to control a 12volt pump on a weed sprayer, This video explains the machine - Input 12 V from a car battery. - Output 12v to a small poison spray pump. - Poison control pump 12V 10 amps draw - low-cost solution without wifi or BLE As described in the video we need a device to replace the operator’s thumb on the control button for the machine. We need to be able to adjust the length of time the pump runs at a factory level – this run time will be set up before the unit is delivered to the end user. We need to have the operator with the ability to adjust the frequency the pump runs

I'm looking for experienced electricians to help with a medium-sized electric panel installation or repair project. The panel is 200-400 amps and requires repair, in particular. The timeframe for repair is flexible; there is no specific urgency. The ideal candidate must have a good track record of electric panel installations and repairs and will be required to provide proof of relevant work experience prior to commencement of the project. If you are confident that you have the right skills and experience, please get in touch.

1. Input: 9~36vdc, Output 24vdc, 10 Amps, Max 1% THD @ full load 2. Design must fit inside an 85mm round x 30mm deep enclosure 3. Components rated for 85 deg C max temperature 4. Need a schematic and data sheets for components used 5. Must be CSA certifiable using UL, UR and/or CSA components 6. Must utilize standard components (not ASIC devices) 7. Will require breadboard testing of design for approval 8. Domestic USA Project

I am seeking an experienced electrical engineer to perform a load analysis and service calculations for my commercial building project. The building is 107,000 square feet and will be used as office space and a warehouse for shipping and receiving. The maximum expected electrical load is more than 200 amps, Phase 3. We have the Light Plan Power Plan and Scheduled done and we can collaborate with that aspect of the project as we are Architectural Designers. The Ideal candidates for this project should have expertise in: - Electrical engineering - Load analysis and service calculations - Commercial building electrical systems - Warehousing electrical systems The project deliverables should include: - Detailed electrical load analysis and service calculations - Expert Eye on the Pow...

I need to control 30 heaters that pull 3 amps each. Power will be 208/ 3 phase. Wanting to design a box that I could plug the heater cords into and then use a computer to control the temp. I have the computer end figured out.

I’m looking for a skilled electric engineer to create a calculator for me in excel. The calculator must tell me what size conductor (Specified in mil) I need to han...Single conductor in insulation b) Twisted pair in insulation c) Twisted pair with shielding in insulation • Conductors resistivity (Verify copper is 1.68E-08 Ω/m ) • Length of conductor in meters • Temperature differential. • Type of insulation (Types of thermoplastics at varying thicknesses, one side of the insulation will be thinner than the other sides.) • Volts • Amps • Frequency (Hz) • Power cycle duration. Power may only be briefly, milliseconds to seconds, so this could be a crucial part of the equation. Hopefully that’s all t...

Voltage sensing ground switch. Switching at 6VDC and 9VDC. Purpose. I have a sound card that operates between 6VDC and 24V DC and between 1 and 2 amps DC. It has 3 sounds installed. I would like at 0V for one sound to play. At 6V it switches to another sound. At 9V it switches to another sound. So each sound plays individually as the voltage increases. When the voltage drops down the sounds also roll back. The ground on the sound board triggers the sound changes. The board I use is DY-HV20T sound board. I would also appreciate if a sample was built and tested, and supplied to me with a circuit diagram. If I can answer any questions, please contact me. Many thanks.

I need a qualified electrical engineer that give us accurate readings and electrical related information on a range of different appliances. Information would need to include things such as: - Power input - Voltage - Amps - Frequency - Average power consumption - Max power consumption etc...

... I will need individual vector-based components as I will be implementing this in my app where the gauges will move and scale as well as numbers to change. The most important information to display is: * Watts (0-25kw)(0-25,000 watts) * Speed mph or km (0-100mph) * Battery %(0-100) other information: * battery volts(0-140v) * Controller temp(0-100c) * Motor temp(0-180c) * Battery amps(0-200a) * motor amps(0-450a) * Error like on a car ⚠️ or ⛔️ * angle(0-60 degrees) * g force(0-1.5) decimals probably like .5 * a Bluetooth connect button: something like green for connected and red for disconnected * a settings/configuration button like a gear or wrench symbol if this goes well I have other screens to design in the same theme as the dashboard like: * Bluetooth device con...

...current monitor sensors for utility-scale solar farms for string monitoring. Essentially we require easy to install sensors on 10 AWG PV wire, up to 32 strings (wires) per combiner box location, installed outside on the wire and tied into a low-cost antenna. We would want this to be a distributed network that ties into one main enclosure onsite that has remote satellite / 5G capabilities. Average amps will be 20-30 per wire, running at 1500 volts since this is utility-scale. Here are some factors: Must be easy to deploy, low-labour, must have high security, safety in mind and meet all local electrical regulations of the Electrical code of Canada, NEC in the US, and cUL certification. Must operate in -40C temperatures, and support harsh environmental conditions -Up to 60Amps -Wi...

This post is for the electronics engineering side of a project to figure out an inexpensive way to make a waterproof mat that would survive an indoor environment for a few years, tha...as Velostat or Linqstat that reduces resistance under pressure. However, I need you to design the circuit for it. The circuit should minimize battery consumption while also obtaining a strong enough signal from the mat to minimize false positives due to stray voltage from passing mobile phones, WiFi and mobile antennas, or a standard U.S. 120V 60Hz electrical cord laid across the mat passing 10 amps or less. If you were to design around this material, I would also need you to locate the specifications of the Velostat / Linqstat material and confirm that it is expected to survive the above-described...

...CHARGER FOR EV, OUR SENIOURS ALREDY DONE A EV MOTER BIKE. SO WE WOULD LIKE TO START FAST CHARGER., OUR CHARGER REQUIREMENTS Specification Unit Charger type Should be adaptable for both LFP and Li-NMC batteries by varying the software settings and flashing the codes Battery Combination 19S6P Battery voltage 60 V Charging Current requirement 15 Amps (should be adaptable to charge at 10 amps too) Noise levels (in the charging current) + or – 0.5 amps Method of charging (CC-CV) CC-CV charging CC cutoff voltage Can be varied according to the voltage requirements Max. Cell cutoff voltage Can be varied according to the voltage requirements Charging status indictor Yes (either through LED or digital) Cutoff temp ~45 DegC Thermal protection availability Yes Colling m...

I plan to use a TPS54283PWPR from Texas Instruments in a project I am working on. I need an experienced engineer to help design my schematic and to ensure I have not made any silly mistakes (before I commit to the PCB) - alternatively, if this proves to be the incorrect part I will need help to identify alternative. A...TPS54283PWPR from Texas Instruments in a project I am working on. I need an experienced engineer to help design my schematic and to ensure I have not made any silly mistakes (before I commit to the PCB) - alternatively, if this proves to be the incorrect part I will need help to identify alternative. All I need is a reliable DC DC converter with 24vDC input and output 1 = 5v at about 2 amps and output 2 at 3.8v at about 1.5 amps (I'm struggling with the m...

I need a circuit design & fabrication of a prototype unit to limit and dissipate high voltage spikes on a 600 VDC, 3.5 kW power system. A small wind turbine on my farm produces up to 3.5 kW, 600 VAC,3 phase power at wild AC frequency (0 to 200 Hz?). A full bridge, 3 phase rectifier takes the wind turbine output & generates 0 to 600 VDC, single phase, single leg, at varying amps, with some noise. If the rectifier output voltage exceeds 300, 400, or 500 VDC (switch selectable), the rectifier engages a load dump heater to dissipate excess power and control maximum voltage output. The rectifier's DC output is fed to a Morningstar Tristar MPPT Charge controller (Model: TS-MPPT-60-600V-48) so as to charge a 48 VDC battery bank. This $2,000.00 Tristar is extremely sensitive...

...Here Battery Type: Lithium NMC – Bluetooth Enabled Battery Capacity: Standard 48 Volt 60 Amp Hour(2.88 KWH) Capacity, Upgradeable In 30 Amp Hour Increments To 180 Amp Hours (8.64 KWH) Estimated Travel Range: With Standard 60 Amp Hour Lithium Batteries On Flat Terrain With 200 Pounds Of Passenger And Gear Approximately 50-60 Kilometers On A Full Charge Charger: Onboard, Waterproof 58 Volts, 8 Amps Output, 120 VAC Input (Optional High Rate 25 Amp Charger Available) Charging Time: Approximately 8 Hours From Fully Discharged Frame: Aluminum Alloy: Aircraft Grade Maximum Speed: 48 Kilometers Per Hour (30 MPH) Factory Set Speed: 35 Kilometers Per Hour (22 MPH) (This Can Be Limited If Required) Braking System: Hydraulic Rear Disc Parking Brake: Electric Additional Safe...

...Conventional Lead Acid Batteries Completely Sealed, Built In Safety Features, And Premium Lithium Ion Cells Come Together To Create A Battery That Weighs Only 40 Pounds, But Can Replace Over 300 Pounds Of Corrosive Lead Acid Batteries. Heavy Duty Design Our Heavy Duty BMS Has Been To Designed To Handle The Large Surge Of Energy Required When Accelerating. The Battery Can Handle 120 Amps Continuously And Up To 360 Amps For 1 Second. Most Stock Golf Carts Can Run On Just One CanLiFe Battery Integrated Bluetooth With A Free IOS And Android App - Monitor Your Batteries State Of Charge, Number Of Cycles, Internal Temperature, And Even Allows You To Turn Discharge On Or Off To Secure Cart Or Prevent Unwanted Drain Of Power By The Cart When Not In Use Backed By The Best Warr...