Allegro PCB designer needed to rework BeagleBone PCB ([login to view URL]) into our custom PCB outline.
Custom Board size
100mm x 32mm + PCI express 38 way edge connector.
To the PCIE connector (not standard compliant signals) connect -
16 contact Series terminated with 47R direct to uP any GPIO pins -No driver IC
4 Input pins via 47R resistors connected direct to uP signals – SPI1_D1,mcasp0_axr3,mcasp0_axr2
8 Output pins via driver (74xx245 type) connected to uP signals –
SPI1_D0, SPI1_SCLK, any_GPIO, mcasp0_ahclkx, mcasp0_aclkx, mcasp0_fsx, mcasp0_axr0, mcasp0_axr1,
Add 4 pin SIP connector for UART0
Flip Ethernet connectors t reverse side
Flip and Rotate USB-A connector so a flash drive will sit parallel on the back of the board.
In order to fit into the reduced size PCB Remove any or all of the following
DC Socket (Figure 9 excluding U2 – Reroute PIN 10 to PCIE 5V connector)
PMIC Expansion (Figure 13) and connector (Figure 25, P6)
46 pin expansion connectors (P8 and P9)
FTDI2232 and support circuit (eeprom,xtal,decoupling,pll)
USB HUB (Figure 15 in BONE_SRM) and support circuit and connector.
Reduce the size of the JTAG connector to 6 Pins (GND, TRST, TCK, TMS, TDI, TDO
I have 8 year of Electronic designs. I'm currently working for international electronic design company.
I am rich experience in Allegro(Cadence)
I'm a lead designer of High speed applications (FPGA Based PC cards equipped with DDR2/DDR3 memories, Gbit links, High speed clocks, PCI-E, USB2.0/3.0, High speed FPGA FPGA interfaces, etc).
You will get full PCB design, BOM and full documentation from me
Dear Sir,
We are Reserach and Development company whose working area are :
-Digital Motor Control
-Analog Design
-Electronic Design
-Power Electronics
-PCB design
-Embedded system
-Matlab
-Simulation of hardware
For each concept descriptions are as follows:
Digital Motor Control:
-3-phase induction motor vector control drive
-Flux estimation algoritm generation
-DSP(TMS320) implementation on motor drive
-Low speed application
-Torque and speed loop generation
-Control algoritms
Analog design
-Low power distribution
-Noissless special opamp based analog circuits
-Analog filters
-Orcad simulation of several circuits
Electronic Design
-RF transmitter and receiver
-Bluetooh reader and transmitter
-Magnetic reader
Power Electronics
-Implementation motor drive
-AC/DC converter
-DC-DC converter
-Battery charger
-Solar inverter
-Renewable Energy simulations
-Uninterruptle power supplies
PCB design
-Schematic design by Altium
-PCB design by Altium
-Power board design
-SMPS board design
Embedded system
-PIC18,PIC24,PIC30 and dsPIC applications
-Ardino
-MSP430
-Atmel
-DSP(Texas Instruments)
-Renesas
Matlab
-Power Electronics simulation
-Motor drive
-Wind Energy
-Solar Energy
-Control applications
Simulation of Hardware
-Orcad Simulation(TI,National, Linear Tech, Maxim libraries)
-LTI
-National
-Matlab
Very important Note: References attached. Please look excel file to see projects which we made until now!
Note: Payments will be funded as:
1)Initial:%25
2)Second stage:%15
3)Third stage:%20
4)Final stage:%40
Metin Akin
I am a electronic engineering with 5 years of experience. I can design schematics and PCB layout with Eagle CAD Soft. I can use other development environments for hardware design.
Sir I can do these for you in 4 days I'm a experienced user of Altium Designer10 and have received from the IAC (Industrial Advisor Committee) the ,,PCB
Designer" degree, as a recognition of their high level of knowledge in the field of CAD for development
of electronic modules and assembliesin 2011, and 2012 in TIE(INTERCONNECTION TECHNIQUES IN ELECTRONICS).
Hi there. I am interested to handle this project. I have 6 years of experience of designing pcbs of different kinds. Job completion with satisfaction and meeting deadlines is guaranteed.
Thanks