Yaskawa a1000 usb driver jobs

URGENTT PROJECT. The project would be to design and build a PCB device and 3D Printable enclosure that supplies power via POE (power over Ethernet) to equipment and can accept a standard construction equipment battery from a manufacturer such as Dewalt, Ryobi, etc. to provide the power to the attached device. There should be 2...Dewalt, Ryobi, etc. to provide the power to the attached device. There should be 2 Ethernet ports (an incoming and outgoing ethernet port) supporting 5Gbps and the power draw will be selectable via switch or button. The power will need to conform to the standards for 802.3af (POE), 802.3at (POE+), and 802.3bt (POE++) and include a power meter that shows the amount of battery power remaining. A USB-C port should also be included. The enclosure should be 3D ...

...internal processing on the micro-controller with isolated signals and ground. Two AB incremental encoders shall be connected to the board. Power Requirement: The board should operate effectively on a 5V DC power supply via USB. Functionality: It is like a signal sniffer. 1. Input and output are the same signals: two single-ended AB encoders, i.e. 4 lines of 5V DC and a common ground 2. Isolate the inputs and ground and connect them to the Arduino-compatible microcontroller like ATmega2560. Use interrupt pins to connect. 3. The power and communication should be provided via USB. 4. Use micro-controllers with built-in boot-loader or otherwise take care of the boot-loader flashing to be compatible with Arduino framework. Preferred PCBA design software: Autodesk EAGLE or ...

...Part A has a single function that function is to transmit a signal. The part needs to be housed in a waterproof container and be powered by a rechargeable battery preferably through USB. This part will actually go on a dogs collar. The device can either transmit vi. RF, USB or any other short range signal. Part B: Part B its job is to have two functions. The first function is to receive a signal from Part A, the second job of Part B is to transmit a specified RF signal to Part C when Part A is within 2 to 3 feet of Part B. Part B, needs to also be housed in a waterproof container and be able to be charged via USB. Part C: Part C, is a separate module that is already created its job is when it receives a specified RF signal from Part B it activates its predesigned ...

I'm looking for a professional mobile app developer to create a driver app for both iOS and Android. Key Features: 1. Login with your Car number in the Chauffeur Login section 2. Enter the OTP Received to login 3. Accept / View the booking received for the next 4 hours 4. Click on “start ride” button 5. After reaching the pickup point click on “Report” button 6. Once customer is picked up, enter CRN number and upload a picture of odometer to start the journey 7. Once reached the drop point, click on “Drop” button, upload a picture of odometer to end the journey 8. Share your Trip Feedback. 9. Click on add Extra charges button for adding extra charges amount and upload a proof for each amount (receipt or transaction screenshot) 10. Extra ch...

Hello am from the Republic of Guinea in west africa. I am planning to start a business in transportation of passengers inside the capital. I am planning ro recruit a driver and his assistant to run the bus daily. It is a profitable venture here,But the problem is that drivers here are dishonest and unaccountable( steal from the daily income) to the bus owners. So i am looking for an expert in a smart electronic system that i can put in the bus for delivering tickets automatically to passengers.

...regulation. This project requires expertise in high-power applications, voltage regulation, and serial communications. Project Requirements: Microcontroller: RP2040 chip to manage all operations. Power Handling: Board must handle input of 24V. Voltage Regulation: Conversion of 24V input to 12V and 5V outputs. MOSFETs: 5 MOSFETs for 24V, 7A control. 4 MOSFETs for 12V, 5A control. Communication: USB Type-C for robust serial communication. Inputs and Outputs: 2 analog inputs. 1 One Wire communication interface. Additional pins for digital input/output as required. Deliverables: Complete PCB design files ready for manufacturing, including gerber files. Schematic capturing and PCB layout. BOM (Bill of Materials) with sourcing options. Documentation for assembly, testing, and troubl...

I'm looking to produce a live-action promotional video to showcase the features of my product. The video is intended to be the primary driver for increasing product visibility and potentially driving sales. Key aspects of the project include: - The video should be vibrant and engaging, with a clear focus on demonstrating the product's features in a compelling manner. - I'm open to creative input from the freelancer regarding the best locations for shooting. The video can be shot indoor, outdoor, or a combination of both. - Given the live-action nature of the video, the freelancer should have experience in working with actors and directing video shoots. - It's essential that the final video is of high quality and suitable for social media and other digital pl...

I'm looking for someone who has very good experience in Laravel's real world situation. What Queue drivers are available in Laravel? Will ignore any replies without answering to the above my question. Here is my problem now. We are using Laravel project and it's running on production. It's using Queue heavily and queue driver is database now. We are getting following issue. SQLSTATE[HY000]: General error: 1205 Lock wait timeout exceeded; try restarting transaction (Connection: mysql, SQL: select * from `jobs` where `id` = 111111 limit 1 for update) Let me know how to fix this then I will hire you immediately and you can be employed in our project. Please don't waste my time if you don't know what's going on with the above message.

As someone with a learner's permit, I need a local driving instructor to help me pass my upcoming driving test. The successful tutor needs their own vehicle that I can use for the practical test at the DMV, and take me to the DMV on the test day. I have not scheduled my test day yet, but I prefer to take it before May 20. I will pay $25/hr. Requirements: - Offer both weekday and weeke...Ability to instruct on parallel parking, highway driving, and defensive driving - Experience in preparing students for the driving test Ideally, I would like a flexible, patient instructor who is skilled at teaching. Knowledge of local DMV expectations for the driving test would be a significant bonus. Your lessons will help me to not only pass my test but also to become an upright and considerate...

I need help diagnosing issues with my car. Specifically, I'm having issues with the air condition, minor issue with handbrake releasing, driver-side window automatic rising, and minor issue with windscreen liquid leaking. The car is a 2010 Audi Q7, and this issue has been going on for more than a month. I'm looking for someone who can take a look at the car and diagnose the problem so I can get it fixed. Will ask for further help to fix the issues if goes well.

I'm in need of a experienced furniture moving driver to join my team. The role would involve the secure delivery of office furniture from Monday to Friday. Key Responsibilities: - Secure office furniture in the truck - Drive furniture to various locations - Safely unload furniture Employment Details: - This is a full-time position Ideal Qualifications: - Previous experience as a furniture moving driver - A valid driver's license - Clean driving record Prospective candidates should be capable and confident in handling and transporting office furniture securely. Experience with furniture coverings and tie-downs for transport is highly desirable.

...background to handle an on-site installation of computer peripherals and networking devices, including a DVR/NVR and Point of Sale (POS) systems to a retail shop inside the Airport terminal. Key Details: - The project involves the following: 1. Connecting a POS computer, monitor, receipt printer, USB card reader and providing remote access to our helpdesk so our techs can configure the system. Work with our helpdesk to test the printer, touchscreen and card reader. 2. Connect a USB camera that measures foot traffic and work with our help desk to configure and test. 3. The building contractor has already set up Ethernet cables and a patch panel. Ideally, you will have tools in case one of the jacks doesn't work it can be tested and crimped quickly instea...

...passengers have been accommodated, after which it will proceed to the destination. Key Features: - User Registration: The app should allow for easy and secure user registration. - Shared Taxi Request: Users can request for a shared taxi through the app. - Real-Time Location Tracking: The app should be able to track the shared taxi in real-time, allowing users to know the exact location. - Passenger and Driver Monitoring: I would like the ability to monitor both passengers and drivers for safety and service optimization. User Interaction: Users should be able to request a shared taxi through the following methods: - By manually entering the desired address. - By selecting their location on a map. Additional Information Collection: In addition to basic details, the app should al...

For Task 1, the project will focus on analyzing flight simulator data using MATLAB to compute metrics that quantify pilot control behaviors during different landing phases, contributing insights into enhancing fly-by-wire systems. In Task 4, MATLAB will be employed to simulate driver responses in automated vehicle scenarios, particularly modeling how drivers might react during rear-end collisions. This simulation will help in assessing the impact of various time gaps on collision avoidance, providing valuable data for improving automated vehicle design and safety protocols.

I am looking for a skilled mobile app developer proficient in iOS, Android, and Windows to create a comprehensive fleet management system. This application should include: - Real-time GPS tracking to monitor and coordinate the movement of the fleet. - A vehicle maintenance tracking feature to ensure timely maintenance of the fleet vehicles. - Driver performance monitoring for managing and improving driver productivity. - Option to create pickup tickets and facilitate communication via text messages within the app interface. - An admin dashboard for overseeing all fleet operations. The dashboard needs basic customization incorporating our brand color and logo. - A payment feature for financial transactions. An ideal freelancer for this project should have previous experie...

Carma is looking for a Driver Valet to help with the transportation of our clients' commercial vehicles to and from auto repair shops. This role requires the Driver Valet to coordinate with a teammate, ensuring one person drives the client's vehicle while the other follows in a separate car to provide logistical support and transport back to our headquarters. The task involves parking at the client’s business, retrieving the commercial vehicle keys, driving the vehicle to the designated repair shop, and handling key exchanges. Upon completion of the vehicle service, the Driver Valet will also need to return the vehicle to the client's location. This position demands strong driving skills, excellent time management, and a commitment to safety and cu...

...the following functionalities: - Virtual COM via USB - Embedded C programming - Keil MDK 6 integration In addition to these core requirements, the project must also meet performance constraints - this must be carefully considered throughout the development process. I'm looking for a freelancer that is able to develop the code from scratch. It's important that you have a solid understanding of embedded systems, as well as experience with USB communication protocols. Your familiarity with Keil MDK 6 is also crucial as it will be the primary IDE used for this project. A background in working with STM32 microcontrollers will be a big plus. In summary, the main tasks for this project include: - Design and implementation of a Virtual COM via USB - Developin...

I am in need of an experienced mobile app developer who can add new features and integrate a payment gateway to a StackFood application I currently have. Here's what I'm looking for: - Addition of New Features: Autoprint and Driver Tips %. The Autoprint feature should automatically print orders and provide customers with receipts. - Payment Gateway Integration: This is to be specifically done with Yoco. Knowledge and expertise in similar customizations would be beneficial. This project requires extensive understanding of mobile app development and integration procedures especially in the context of the StackFood app. Your portfolio showing similar projects will be greatly appreciated. Looking forward to your bids.

As the main driver of this project, my primary requirement is a proficient Designer to create a corporate and professional styled research report. The primary aim is to effectively present findings to external business stakeholders. The ideal candidate for this task would have: - Proficiency in designing corporate and professional styles. - Exceptional communication skills. - Experience designing business reports. - An understanding of how to communicate data visually in a way that appeals to external stakeholders. Understanding how to present complex findings in an accessible and understandable way is crucial. Your design should enable the report to influence decision-making among business stakeholders effectively. I am expecting high quality and timely delivery. Apply if you be...

I'm in need of a personal driver who can assist me with daily commuting on 3 days of the week. Key Responsibilities: - Drive me to and from work - Ensure a safe and comfortable commute This is a part-time role and the selected driver will be required to work 3 days a week. Skills & Experience Required: - Valid driver's license - Experience in personal driving - Good driving record - Punctuality and reliability Please provide information on your availability and experience as well as any references you can share.

...ride-hailing application that offers a similar experience to Uber and Ola. The app should be available on both Android and iOS platforms. Key features I'd like to include are: - **GPS Tracking**: The app should be able to track and display the real-time location of the driver and the customer. - **Payment Integration**: I need the app to have a seamless payment system for my users. This includes integrating popular payment gateways. - **Driver Rating System**: A feature that allows customers to rate their ride experience and review their driver. I am not looking for support for multiple languages at this time. The ideal candidate should be well-versed in mobile app development with experience in creating and launching similar ride-hailing apps. If you...

...and monitor to work via a desktop host. Key Project Features: - **Repurposing Old Hardware**: The main aim of this project is to make use of an old laptop's keyboard and monitor. The PCB should make it possible to connect these to a desktop host. Ideal Skills and Experience: - **PCB Design**: You need to have a strong background in designing PCBs. It's crucial that the PCB you design supports USB and HDMI connectivity, and allows for key mapping and backlight control for the keyboard integration. - **Embedded Systems**: Experience with embedded systems is a big plus as it helps in seamlessly integrating the keyboard and monitor to the desktop host. - **Hardware Repurposing**: Understanding of how to reconfigure old hardware for new purposes will be highly beneficia...

... 2 producs 2 products 4 products 2 products • Off-Highway Machinery • Agricultural Machinery Off highway and agriculture each will have the following products: 2x products 2x products 2x products https://specdiag

...doors are to have a self-closing mechanism, smart locks with fingerprint, facial recognition, the garage door must be armoured please see link before for examples of doors and gates all internal doors must also be armoured with a self-closing mechanism as well but must bust be light enough for a young child to open and close with ease. All socket outlets are to be UK standard 3-pin sockets with USB type C ports, all lights to be led, all heating is to be done by electrical heaters and AC, main entrance should have a led chandelier. Property to get power from battery 2x battery packs that can individually be turned off in an emergency or when under maintenance, solar panels to be installed on the roof for power for the whole property and to charge the batteries, battery packs to...

...add/remove elements, also ‘open source’. Most of the requirements can be found in any CM4 carrier board available with a public license, for exampe CMIO from raspberry pi. Description of the elements, interfaces and other requirements follows • Maximum board size 100mmx200mm aprox. • Power souce 12v, protected and converted to other DC (present in CMIO) • USB-C with mini USB conector for programming (present in CMIO) • USB 3.0 (present in CMIO) • Ethernet (present in CMIO) • CANBUS • PCIe (present in CMIO) • SD card slot (present in CMIO) • HDMI to LVDS signal + backlight • AIS class B • Other UART inputs with optocouplers (to be decided) • ...

I have an Orange PI Computer Module 4 and need a skilled Linux developer to set up a linux with appropriate drivers for several devices. The main requirements for this project are: - Driver setup for: - Two cameras. The primary purpose will be for image capturing. - One eDP display. - One RGB LCD display. I am aware it's an unusual requirement, so I would appreciate it if you could confirm whether it's possible. - One MIPI display. Note: Only one type of display will be used at a time. The main goal of this project is to have the Linux system up and running with the necessary drivers for these devices. The displays should function independently, showing different outputs, with basic interactions. Your experience with Linux system configurations, drivers setup,...

I am looking for a freelancer to creating a custom carrier board that is specifically designed for Raspberry Pi Compute Module 4. Features: - It should include an Ethernet - Type-C USB port power power. - We're also looking at equipping it with a 4G mobile module (SIM7600 or equivalent that work in Australia/Telstra). - 1 X Sim slot. - 2 X External antenna connectors SMA - 1 X Power LED for CM4 - 1 X Activity LED for CM4 - 1 X Multicolour LED for signal strength of mobile module. - The carrier board should be made as small as possible. Skills and experience: - Freelancers interested need proficiency in electronics and PCB design, along with a deep understanding of Raspberry Pi Compute Module 4. Experience in custom carrier board design and SIM7600 or equival...

Please turn this photo into a STL file- Box is 7x7x3cm Also make a lid that fits the top. inspired by other photo, on the with same text either engraved into the lid or standing out The holes on the side of the box should all be removed. In the left there should be a USB C port in the right there should be a 8mm hole for ethernetcable

As the project owner, I am seeking a talented development team to build a robust, all in one grocery delivery mobile and web ap...Admin platform to view orders and allocate drivers ● Google Maps to allow admin to view order location on a map (no live journey tracking) ● Customer ordering system using Stripe for payment direct to Wee Drop (no Stripe Connect or third party vendors) ● Partial refund system via Stripe for admins at their discretion ● Delivery statuses (Pending, Canceled, Driver Assigned, Delivered, Un-Deliverable) ● Admin assign drivers or driver self-assign via web-mobile page ● Drivers can view customer’s phone number ● Admin dashboard to view orders, create listings, view team users, view drivers ● Customer can see estimated delivery time set by ...

I am looking for an experienced Android Studio developer to create a comprehensive taxi booking app similar to Uber. The app will be aimed at the general public and should include the following key features: - GPS Tracking: The app must be able to track user location and match them with the nearest available driver. - In-App Payments: Users should be able to pay for their rides directly through the app. - Ride Feedback: After the completion of each trip, users should be able to rate and provide feedback on their experience. The core matching mechanism should be based on proximity, ensuring a seamless and efficient user experience. Ideal skills and experience for this project include: - Proficiency in Android Studio - Previous experience with GPS integration in apps - In-depth kno...

Hello, i need someone good programmer who is able to modify ASF CDC echo example for atsamd11d14 mcu. When receive '1' by CDC -> set 2 pins of mcu When receive '0' by CDC -> reset these 2 pins of mcu And i would like device to be visible in Device Manager or Linux like 'USB CDC'

I'm looking to develop a comprehensive garage management software that we can offer as a SaaS product. This software will cater to garage owners who can subscribe to use our services. It should have the following features: - Customer Management: A system to manage customer data, appointments, and services. - Appointment Scheduling: A robust and flexible appointment scheduling s...Ideal skills and experience for this job include: - Proficiency in SaaS software development - Strong background in UI/UX design - Knowledge of garage management systems - Experience with implementing notification systems - Ability to work with APIs - Excellent communication skills and a proactive approach to keep me updated on the project's progress. admin . android apps and ios apps including d...

...Part A has a single function that function is to transmit a signal. The part needs to be housed in a waterproof container and be powered by a rechargeable battery preferably through USB. This part will actually go on a dogs collar. The device can either transmit vi. RF, USB or any other short range signal. Part B: Part B its job is to have two functions. The first function is to receive a signal from Part A, the second job of Part B is to transmit a specified RF signal to Part C when Part A is within 2 to 3 feet of Part B. Part B, needs to also be housed in a waterproof container and be able to be charged via USB. Part C: Part C, is a separate module that is already created its job is when it receives a specified RF signal from Part B it activates its predesigned ...

...the container. Project Requirements: Pipeline File Creation: -Automatically generate 13 blank pipeline files as placeholders to verify the initial setup. File Transfers: -Transfer 13 pipeline configuration files from the host to the container, specifically to /usr/share/logstash/config. -Move the configuration file from the host to /usr/share/logstash/pipeline. -Transfer a JDBC driver from the host to /usr/share/logstash/config. Java Keystore Setup: -Configure a Java Keystore on the host with 5 variables (names can be placeholders). -Transfer the Keystore file from the host to the container -Validate Keystore file works successfully Cron Automation for Pipelines: -Set up a cron job to run each of the 13 pipelines hourly, starting at 02:00 AM, with subsequent pipelines runnin...

I'm looking for an experienced graphic designer to create a modern-style business card for my private driving business. The card should be impactful with a black background. The required information to be included on the card are my Name, Contact Number, and Email Address. KEY DETAILS: • Modern design style • Black background color • Include: Name, Contact Number, and Email Address IDEAL CANDIDATE: The ideal candidate should have a strong background in graphic design with a portfolio of business card designs. Proficiency in modern design and relevant software are also required.

I'm in need of an expert who can assist me in writing Python code and simulating circuits on Raspberry Pi 3 with Proteus 8. ...Python code and simulating circuits on Raspberry Pi 3 with Proteus 8. This is specifically to execute stepper motor functionalities. Being able to debug the code would also be an added benefit. Key skills and experience: - Proficiency in Python programming - Experience in Raspberry Pi 3 coding - Expertise in Proteus 8 simulation - Understanding of stepper motor operations.(28BYJ-48),ULN2003 motor driver I use 2 rc car one should connect with each other send .First rc car should send (x,y) coordinates and its speed to second rc car and act upon the information. Should get the project within 1 day last date 30/4/2024 Your expertise will make this pro...

As a growing provider of logistic services, I am in need of a seasone...dispatcher who can handle both truck and freight dispatch. The scope of services to be provisioned includes not only basic dispatch services, but includes load planning and route optimization as well. Additional requirements. - Speak fluent English - Speak Russian or Ukrainian Key Responsibilities: - Truck and freight dispatch - Load planning - Route optimization - Broker communication - Driver communication Ideal Skills: - Proven experience in truck and freight dispatch - Proficient in load planning and route optimization - Excellent communication skills - Ability to manage between 10 and 50 shipments daily. Your expertise will help streamline operations while maintaining a high level of client sat...

I have an application in Ubuntu 16.04 that's written in C++. It randomly crashes every few hours, and I suspect it may be related to the usb microphone. I need an expert in debugging to diagnose and fix the issue. Key Points: - The crashes are occurring during idle or background processes, but I'm not entirely certain of the exact trigger. - The freelancer must be fluent in C++ and have a high level of proficiency in debugging on Ubuntu systems. - Prior experience with usb microphone-related issues in C++ applications is a plus.

...MCUs firmware and software development. Our ideal candidate would primarily help us develop a Windows, Linux, and macOS compatible monitoring system, specifically for voltage. The goal is to create a GUI application with specific features. These include: - Real-time monitoring - Graphical representation - Data logging - GPIO MCU ON/OFF control - Voltage and current real-time transfer to PC via USB-connected MCU SAMD21 This calls for not only proficiency in GUI application development, but also a demonstrated understanding of working with real-time data transfer systems. Real-time voltage monitoring and the know-how of system-level development will be crucial to this particular project. If you've delivered similar projects in the past or think you are well-aligned with ...

C++ expert. I have basic code. Want to stream the data from usb camera and show camera image. And some task with opencv.

...<Technology Description> This technology is a new control method for autonomous vehicles. Traditional autonomous vehicles detected other vehicles and displayed this information inside the car to inform the driver of the surrounding conditions. However, it may be difficult to identify which vehicles require my vehicle to adjust its speed when many vehicles were displayed. In this technology, the vehicle which requires my vehicle to adjust its speed in autonomous operation is displayed with a special shaped icon, and if it is in the next lane or closest to the vehicle, it is highlighted. This allows the driver to easily identify the target vehicle for speed adjustment. This supports the safe operation of the vehicle. Please search for this technology in this contest. ...

...obstacles ahead, and stops the car to prevent collisions. However, there is a possibility that the car may start moving when the brake pressure is released while not operating the brakes, so a technology has been proposed to maintain the stopped state for a certain period of time. In addition, under certain circumstances, it also has a feature that does not release the car's stopped state until the driver operates it. Please search for this technology in this contest. <<NOTICE>> The target car brands in this search are limited to Jaguar or Land Rover. <Requirements for Payment> ・Submit documentary evidence that clearly states the details of the subject product, the name of the company selling the product, and the company that plans to sell the product. ...

...of your vehicle based on the driving line of the vehicle in front, and operates to maintain the target driving line. In addition it also has the ability to adjust the speed of the vehicle to maintain a certain distance from the vehicle in front, and the ability to drive the vehicle according to the driving pattern of the vehicle in front. Furthermore, this device stops automatic steering if the driver manually changes the vehicle's position in the width direction of the road and the distance from the vehicle in front exceeds a certain value (condition 1). First, please research the driving assistance devices mentioned above. If you have found the information on driving assistance devices up to this point, please also check the information below. After automatic steering is c...

Want ride hailing taxi app as like as bolt,careem,meneva taxi,onde app etc. I'm seeking a seasoned mobile app developer to build a comprehensive ride hailing application. This app will not be limited to booking rides, but will also enable driver tracking and efficient payment processing. Key Features: - Booking Rides: The primary feature of this app is booking rides. I want users to have an easy-to-use interface for booking rides. - Driver Tracking: A real-time tracking system, through which users can monitor the location of their booked taxi. - Payment System: The app needs to facilitate seamless transactions via credit/debit cards and cash. It is essential to incorporate an integrated, reliable, and secure payment gateway. Vehicle Options: - Multiple Choices: The a...

The sony up-dr150 is the industry standard dye sublimation printer. It prints off a roll of paper, and cuts a 4x6 photo strip off of the roll when done. Because this is an old printer, the driver only works with 32-bit machines. I would like to to work with 64-bit machines I wish to get the driver revised to make it work with 64-but machines and allow the printer to do a "Half cut, basically yielding 2 2x6 photo strips instead. I know drivers have been made for other sony models, but because of the fact that the up-dr150 is discontinued, there is no further driver development.

Please create an ACE Sr one-seat configuration with no arms x7. Red part is battery power - blue part is Pip USB - Please create this configuration in three colours: Olympic Cobalt Cayman Please let me know if you have any questions! Thanks!

Hello, There is a system called galvonometer in laser cutting machines. An electronic card called ezcad2 is used to control the galvonometer system. Our aim is to send the image we obtained with Python OpenCV to the ezcad2 card and process it on the laser. We don't need the opencv part. Send any matrix to the card via USB and have it processed. I'm seeking a developer with proficiency in Python and experience in creating control software to develop a system that fulfills multiple requirements. Key Features: - Real-time Control: The software should be capable of controlling the laser marking system efficiently and in real time. - EZCAD2 Compatibility: The system should be seamlessly compatible with the EZCAD2 software to allow smooth operations. Interface: - Both Co...

I am embarking on a mission to significantly reduce road accidents leveraging cutting-edge technologies. Key Features - The software must integrate Artificial Intelligence, Internet of Things, and Machine Learning to develop advanced features. - It should include real-time road conditions monitoring and driver behaviour analysis. - Furthermore, it will encompass collision detection and avoidance to promptly react in risky situations. Ideal Freelancer - I am hunting for an experienced developer with a strong background in AI, IoT, and Machine Learning. - Expertise in creating software solutions for vehicles and a passion for making roads safer would be a huge plus.

...customize their menu in a user-friendly way, adding and removing items as they see fit. User account types are also essential for this system: - Customer accounts: Accounts for customers to place orders easily, track their history and save their preferences. - Restaurant accounts: Accounts for restaurant owners to manage their menu, view and accept orders, and track their performance. - Delivery driver accounts: Accounts for delivery drivers to receive order assignments, track delivery locations and update order status. I'm seeking a developer with a strong background in food delivery software, who has worked on multi-platform projects. Experience in creating user-friendly interfaces, payment gateways and GPS tracking will be highly valued. Strong communication skills a...

Develop an app which resides and runs of a usb thumb drive. The app needs to launch automatically when the usb is inserted into the Windows computer. App should give a selection of Backup or Restore to the user. If backup is selected, the user is able to select as many folders they need to backup and click ok. The app can show a file/folder tree with checkbox options so that the user can unselect certain sub-folders within the main folder. The user should be given options such as copy without ACLs (file & folder permission settings (similar to Robocopy /B option). The app then checks the total size of all folders selected and checks if the free space available in the thumb drive is sufficient, if sufficient, it proceeds to zip and transfer each folder into the th...