Omnigraffle cisco stencils jobs

I currently have ISDN PRI setup on voice gateway cisco 2951 and CCUM 10.5 with about 50 DIDs (numbers) I have new setup: ITSP SIP trunk to claritytel on my voice gateway and another trunk to CCUM. This is just additional new config to ISDN PRI - existing one. I have user and password from Claritytel. Besides creating both sip trunks we need to create other config so for example using digit 7 in front of any number the SIP trunk is dialed (not existing ISDN PRI trunk) I can provide more information as needed as well as detailed plan. This needs to be completed so I can use that SIP trunk from any Cisco phone in the network.

Hi Ahmed F., I noticed your profile wondering how are you charging to do a project and can you do Cisco Packet Tracer using software version 6.3?

I need help for my cisco packet tracker

Cisco webex is used for conducting webinars. Attendee can register for the webinar and gets the confirmation mail. What we want is: If the event is paid, attendee registers for the webinar and make the payment(This is required) and gets the confirmation mail. We want this payment gateway to be integrated in the webinar Registration. Please note : Its not just integrating payment gateway. The key point is "Integration with Webex"... Look at webex before bidding Looking for urgent and accurate solution Regards, Sharad Mittal

To be required tasks: To purchase/subscribe either commercial or free open source server online. (Cost less than 4 US dollars per month) Install GNS3VM and import all appliances, images, (Cisco images available.

I need someone with lots of Cisco experience to configure one AP's configure with mobility express so it will join the Controller and the other 5 AP's that are running now. This requires in depth knowledge of CLI and Command line in Cisco only. Specifically 1852 AP's

Seeking to allow a participant to edit a Webex recording

I have two L3 switches from Cisco, model SG350-28MP and SG350-10MP that need to be programmed with 2 VLANs one will be VLAN10 Data, with and IP address rage of - 200, with a 24bit mask, and the other one will be VLAN20 Voice, with an IP Address rage of - 200 with at 24bit mask, the DHCP server function will be used on the Cisco Switch SG350-28MP to provide IP addresses for the both VLANs, the switches will be connected using fiber in between them, I would like intervlan routing enable, if this is a good idea, and please keep in mind that the phone has a secondary port that should provide data to the computers or printers that might be connected on that port, also the internet gateway ip address is , this is a normal netgear WiFi router connected directly to

Distributor of affordable watches in south africa. WE are looking to start our own branded watches too. Company name: Cisco Matteo. I have uploaded an idea of the logo that I found on the internet. We are looking for a logo that will not only go only our watches but also our social media platforms.

Task that is already done. Installed Centos os. Installed Asterix server. Task that’s required to do. -Configure SIP trunk and DID number. -Make dial plans for 5 cisco ip phones and integrate with Asterix

Hey! I need a custom WordPress plugin to help me with my videomeetings on zoom and cisco webex. Hope you can help me with this. :-) Timetable and specs: ⁃ I need this to be done withing the next 6 days after order. This is not discussable. :-) ⁃ Please do not offer, if you dont know APIs and Elementor. Here are my requirements: ⁃ I have several custom post types (which I need to select in the plugin settings) ⁃ Every post type needs to create a webex OR zoom meeting with custom field data (Zoom API, Cisco API) ⁃ The plugin needs a config, which post types get what service. When selecting both services on a CPT, on the post creation the user will be asked, which service he wants to use ⁃ These (ACF, or JetEngine - please tell me what you prefere) fields (field mappin...

i need someone to help me on my cisco packet tracer skills assessment

Dear Freelancer I would like to block some sites including social Media sites, Whatsapp ports, Youtube....etc excepted any method DNS or ACL

Installation of FreePBX on DigitalOcean Instance Setup SIPTrunk using Provision Users & Groups Provision Call recording Auto-provisioning for 6 Yealink W52P & 3 Cisco SPA508G Telephones using mac-address Setup Dial Plans for Inbound - Out Bound Routes UK Landline & Mobile Limit calls to UK Mobile & Landline numbers only Bar Access to premium telephone numbers.

To programme a Cisco asa5550 firewall as a 3way firewall / vpn device. The device has 3 ports: 1-external1 used for vpn traffic. 2-Nhs HSCN1 internet traffic. 3-internal1 corporate network. All corp traffic must flow across a dedicated local pwan (already in use across the org’ 192.168/ ) All internet traffic not on the corp network must travel down the HSCN port. All vpn traffic must be able to traverse across the whole network including HSCN internet traffic.

looking for someone skilled in Cisco CLI to help with reviewing some cisco switch config

Dear freelancers, I need some changes to an existing website. I need someone who is very familiar with webex or newrow virtual online meetings/training implementation into the website and LMS. Someone who already worked such projects. I need to integrate one of those or similar platforms for online meetings into my website so they can be used directly from my website. They can be implemented in LMS also and my website has LMS core. Please only freelancers who have experience in such projects to make offer. Best regards.

I want to make a project on cisco packet traser

We have to ip based monitor system on cisco packet tracer in which the doctor can get a alert when the patient temperature gets high for example when the patient temperature gets high it sends an automatic message to the doctor and we also want to the temperature of the patient We also want to show how data is flow from one side to another And we also want to see the patient temperature by our own

Good morning, i need help to use a second ISP (PPPOE) inside a CISCO MERAKI MX64, i configured it but i am not able to use it because i need to use 2 ISP so i configured it not inside INTERNET port but inside PORT 4 of

Hi ramy, I need help with my cisco certificate in an hour

I am looking to have the attached images made into CAD drawing stencils, so that the digital stencils may be used for plasma cutting sheets of metal.

Hi Kazi N., I need help in my certificat cisco in on hour ,at 10:30 p.m. your local time

i want someone who has the experience in working on Cisco packet tracer i want to Create a network diagram using Cisco Packet Tracer with some requirements: and to write a report on what he did thank you

1. Hands on experience for Cisco network and security infrastructure implementation, especially on FTD and FMC. 2. Have working experience of the wide variety of Cisco products and technologies; include core, aggregation, and access routing and Switching, FTD and FMC. 3. Analyse problems, perform troubleshooting, and track problems through resolution 4. Setup and deploy FMC and FTD 5. Configuration of Access Control Policy, Sub Int [Vrf] Creation 6. Config of FTD platform settings 7. Routing Configuration, NAT Config 8. Health Policy Configuration 9. FTD HA Configuration 10. Perform on-site and off-site testing and commissioning and service activations 11. Perform troubleshooting for any issue faced during the security and network deployment.

...I am working on effort with security vendor to establish persistent outbound connections from two internal company hosts to a vendor endpoint. This connection has to be reliable and thus cannot go through a proxy or an in-line filter. I have the source IP and destination IP and port. There are 2 source IPs and 1 destination IP. 2 source IPs are from different location. Servers are connected to Cisco ACI leaf switches through internet. They have white listed company IP on their end. Our Company is accessing the vendor so traffic is going through internet firewalls. Firewalls rules are implemented on Egress Firewall one side and Egress Firewall on other side. I am guessing these 2 source IP addresses are just 2 instances of same application. Firewall is able to see traffic from on...

I need to design a packet tracer simulation for interconnecting two active active data centers. There is a 50 km distance between both data centers. It should be a high availability cluster. Please remember that both data centers should be in active active status and cooperate office and 03 branches should be connected to the network.

I am having issues with Cisco WAP .its clustered ap and having single set up issues with DHCP the wifi is dropping .will provide more details to the right candidate who knows what to is less than 30 minutes discussion a candidate you will be giving recommendations and answering my questions related to Cisco AP. Remember it's not issue based .it's about recommendation and explaining me what each feature does? how to interpret the dash board ? how to find out signal strength? very simple task for a network guy.i will be paying 20Aud.

The tool KCS will be used in order to make a cross check of the technical network KPI for the network probing (do it by Cisco and Huawei device using ICMP and UDP protocols). The probes, Cisco and Huawei, generate n packets per second to the remote sites (remote router), the traffic of these packets give a quality of the network connection. In order to make a cross check of the data exported from the Cisco and Huawei probes the tool KCS will have to collect the traffic in the middle of the connection by a packet capture tool like Wireshark/tshark. The traffic, collected in .pcap format file, will have to be imported in the DB on the tool server in order to calculate and filter the KPI per session of the test (test ICMP or UDP). The PKCS will have to manage from the web...

1. Rack setup & installation of rack servers - Server Rack - Standard 42U (2PDU) (1 Nos) - Servers - HPE DL380 Gen10 (4 Nos) - Storage - HPE MSA 2050 Series (1 Nos) - Switch - Cisco Catalyst 9300L 48p data,4x1G Uplink (2 Nos) 2. Fiber connections of about 60 m 3. Ethernet UTP cabling of above servers 4. Power cabling (UPS power + Main power) - 20m 5. Cable management within rack with proper labeling - Network and iLO / power / Fiber cables from MSA to server / Labeling 6. Firmware update and RAID configuration (Servers / Storage / Switches) - Above mentioned numbers 7. Cisco switch configuration - VLAN with MPLS (with 2-3 subnets) 8. iLO configuration & remote connectivity (servers / storage / switches) 9. Your effort should include hardware redu...

I need someone to remote into a Cisco 1262N, through my computer, and enable the web interface, so I may then configure the AP for use as a stand alone unit.

Networking - Working with cisco packet tracer implementing and testing OSPF, EIRGP, IPv6. examples are in the files uploaded. IP Subnet Design and IP Address Plan tables will all be filled out by me already. I need it implemented to the packet tracer file that I'm giving you and fully working -About 15 questions per lab mostly if not all screenshots making sure that it works. Check out the uploaded the files.

Remote into a Cisco 1262N, through my computer, and enable the web interface

We are looking for a networking expert that is familiar with meraki and could help us to identify the problem with Cisco Room packet loss issue. Please quote only if you have experience in resolving packet losss for Cisco telepresence environment.

Good morning, i need help to create a vlan inside my meraki because i have lan and wan network. Kind regards

routing & switching all routing and connectivity issues. basic cisco routers configuration. best network topology for security and more. 4. configure basic cisco switches configuration. all routing protocols like eigrp and ospf. 6. configure ip at devices faster. configuration . 8. HSRP and redundancy plans. vlans and inter vlan. And more networking work just contact me.

I have 3 locations connected centralized cucm. All locations are with separate sip modem & CME router. The system was working without any issues up to the last 3 years. Unexpectedly one of the branches incoming and outgoing call not working. I contacted the sip service provider they verified and said that they are getting 500 internal server error. Please bid if you are ready to fix the issue and provide step by step guide.

Hello dear, i have a project but i dont have time to do the integration & configuration now, i need to setup vpn server on cisco 2811 router with network to client method. ( Cisco router is behind ADSL router with public dynamic IP) the job should be accomplished within the next two days , deadline 11-6-2020

we are looking for people who has experience to do Virtual Event Application based on API cisco, zoom, or other App.

Cerchiamo un tecnico video che sappia usare: Programmi obs o streamix Piattaforme di webinar/streaming tipo: zoom-gotowebinar- streamyard- cisco webex etc Per alcuni eventi nei prossimi mesi

I have powerpoint slides that need a lot of updates. They need additional explanation, pictures, diagrams, and quizzes added. I absolutely need someone that can start RIGHT NOW because the class starts tomorrow.

I am switching from a Cisco 881 router to a Cisco ASA 5505 router and want to convert the running configuration file on the 881 to a configuration file I can run on the ASA 5505 which requires changing the commands to the ASA format. No new functionality. It may not be necessary to know this but the Cisco router runs behind an ISP router running on its own ip range. There is a VPN connecting the internal office network subnet to a datacenter subnet. I need this ASAP, so please mention credentials, cost and time frame. Thanks.

Hello, I have a cisco asa configuration backup. I need someone to create the same configuration in my fortigate hardware.

...design the website based on that logo you already designed - Top Menu Items: COMPANY - SERVICES - BLOG - NEWS - CONTACT - QUOTE + ( Sales Phone Button & 24/7 Live Support Button ) + Your Logo Design - HEAD BANNER: Why you should Choose GT MANAGED IT - Our Services: Managed IT Services - Business Continuity - VOIP - CLOUD SERVICES - SECURITY SERVICES - Our Clients: Intel - Amazon - IBM - Cisco - Oracon - 24 / 7 / 365 Support - No Hidden Charges - Manage IT Systems - Manage IT Costs - Schedule Your Free IT Consultation Today - Schedule Now Button - Business Continuity: Encrypted and Secure - Offsite Storage - On-Demand Restores - Cloud Integration - Frequently Asked Questions List: Ask new question Button - What our happy clients say - Get in touch...

Hi Cisco E., I noticed your profile and would like to offer you my project. We can discuss any details over chat.

Need a lab to be finished which requires VLSM subnetting on cisco packet tracer with the assigned IP. Please check the attached file.

Inherited a Cisco 5505 Ver 7.2 (not on support) and need it moved to ver 8.4 so a Firepower migration tool can be used to move the IOS code to a new Cisco 1010 we just purchased. 1010 is under contract.

I want someone to create site to site VPN for me, I have all the details in excell sheet.

I need a Network project done in 5 days

...contribute to retrospectives, addressing opportunities to drive incremental improvements • General Administration • Good at documentation • Gain and demonstrate awareness of and working to budgets Prerequisite Skills: • Minimum 10 years’ experience in network/ISP environment • CCIE track • CCNP R&S • CCNA • Strong knowledge of voice networks and telephone exchange systems SBC Ribbon SONUS for ISP • Cisco CCME and CCM • Advanced complex problem-solving skills • Debugging/analytical skills • Good oral and written communication skills, mandatory fluent Italian and English lang. • Eye for detail, self-starting and independent, but able to work within predefined areas of responsibility • Thorough und...