ESP32 with lcd and coin acceptor

Need the following done We need a quite simple point of sale. Following components are what we are putting together. 1 x esp32 1 x comestro RM5 Coin acceptor 1 x Money control hopper MK4 value 1 1 x Money control hopper MK4 value 10 1 x LCD touch 3.2 ILI9327 Following pins are used as below mentioned: LCD-Touch: CS of ILI9327 to gpio33 RS of ILI9327 to gpio15 DR of ILI9327 to gpio02 WR of ILI9327 to gpio04 D0 of ILI9327 to gpio12 D1 of ILI9327 to gpio13 D2 of ILI9327 to gpio26 D3 of ILI9327 to gpio25 D4 of ILI9327 to gpio17 D5 of ILI9327 to gpio16 D6 of ILI9327 to gpio27 D7 of ILI9327 to gpio14 Coin acceptor RM5 input is connected as follows. 1 kr. input = gpio36 2 kr. input = gpio39 5 kr. input = gpio34 10 kr. input = gpio35 20 kr. input = gpio32 The Money control mk4 hoppers are connected to the following pins 10 kr. hopper output = gpio5 1 kr. hopper output = gpio18 The above mentioned input pins receive a 100ms gnd connection for each coin put in, this gnd connection depending on gpio credits either 1, 2, 5, 10, 20 kr to the LCD screen. The point of the project is as follows When a coin is put in on the 1, 2, 5, 10, 20 kr. channels of the coin acceptor, the amount must be shown in the top of the UI on the Touch display. In the Bottom of the UI must be a payout button, where a payout of the credited or remaining amount must be paid out through the 1 kr. and the 10 kr. hopper. So e.g if 99 kr. is credited and a user click payout 9x pulses to the 10 kr, hopper must be made and 9 pulses to the 1 kr. hopper. (1 pulse = 100 ms high). Now to the UI. Main screen. Credit on top (All screens) button 1 2 and 3 payout button. (All screens) Button1 clicked Credit on top (All screens) 18 buttons must show each with a price (might need to be split up in 1-6, 7-12 and 13-18) (When button 1-18 is clicked, price must be deducted from credit.) payout button. (All screens) If payout is clicked, remaining credit must be paid out. Back button (back to main screen). Button2 clicked Credit on top (All screens) 8 buttons must show each with a price (might need to be split up in 1-4 and 5-8) (When button 1-8 is clicked, price must be deducted from credit.) payout button. (All screens) If payout is clicked, remaining credit must be paid out. Back button (back to main screen). Button3 clicked Credit on top (All screens) 2 buttons must show each with a price (When button 1 or is clicked, price must be deducted from credit.) payout button. (All screens) If payout is clicked, remaining credit must be paid out. Back button (back to main screen). When one of the 1-18, 1-8 or the 1-2 with price reduction is clicked, the button must be unavailable for x amount of minutes defined for each in the code.. TBD: a pin must be used to communicate with an Arduino Mega to turn on and off relays. (this will be a follow up project.) Above should be quite simple for anyone that has experience with ESP32 and Arduino IDE, we request that you work over anydesk when testing, since its quite a task to send the equipment. You bid is what you get, so dont low bid to get to chat, and then change your bid...