Ebay motors template jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    2,811 ebay motors template jobs found, pricing in SGD

    Hello Everyone, I have a question in regarding to Ultracapacitors/Motors/Moment, and I need this help within 5 hours. Please do not waste my time if you are not familiar with any of these. Thank you.

    $25 (Avg Bid)
    $25 Avg Bid
    4 bids

    We have an ESP32 that is connected to a motor driver and a led driver. We need to trigger the lights and motors through the BLE connection by the touch of a button or buttons on the Android App. Short and simple.

    $215 (Avg Bid)
    $215 Avg Bid
    23 bids

    Hello, The goal is to control 4 stepper motors with Arduino Mega + Ramps 1.4 with stepper drivers and with Labview GUI. I have the hardware ready. The task is to write the coding/programming so that it all works as planned.

    $16 / hr (Avg Bid)
    $16 / hr Avg Bid
    28 bids

    A worker is needed to write a legacy application in MS-DOS with Turbo C. The program will control stepper motors in an XYZ configuration and output the "step and direction" signals to the parallel port. Please see additional attachment.

    $374 (Avg Bid)
    $374 Avg Bid
    13 bids

    ...to work with me to design a PCB based on the required inputs and outputs? LED flasher LED low battery flasher GPS Module 433mhz transmitter/receiver Lipo battery bay Haptic Motors Speaker Small camera board 2.4ghz video transmitter Listed above are the components I would like as part of the board. Please respond with there process for board design

    $2053 (Avg Bid)
    $2053 Avg Bid
    59 bids
    Nafusa Motors 1 day left

    Portal for Selling Cars, direct deal between the seller and the buyer

    $751 (Avg Bid)
    $751 Avg Bid
    12 bids

    Please view the 3 PDF pages. On each page we'll be blanking out the Stormtech and Velocity Motors branding. Instead of Velocity we're going to add a new brand - Stay and Wander. See their logo attached. Instead of the V logo for Velocity, we'll amend this to a W for "Wander. All of the colors can stay the same.

    $26 (Avg Bid)
    $26 Avg Bid
    24 bids

    We have a theme for wordpress that a auto dealer client of ours uses called Motors by StyleMix. There are limitations to the theme however. We need to add a few buttons to Inventory listing pages. This may be in page template or it may be in theme settings. We need these buttons to persist and always display even if theme is updated. We have attached

    $93 (Avg Bid)
    $93 Avg Bid
    26 bids

    I'm working on a project and there is a part in which i need help. Basically I need a program to operate 4 stepper motors using arduino along with its schematic (preferably in proteus). The sequence of operation will be provided

    $25 (Avg Bid)
    $25 Avg Bid
    31 bids

    Hey - I need a logo created for a business. Tupling Motors.

    $52 (Avg Bid)
    $52 Avg Bid
    1 bids

    ...induction motor use programs for example motor analysis or other. For example: [login to view URL] I need basic operating characteristics. So that compare them. Model of the motors, with the Magnetic field of motor Distribution of magnetic inductions. Characteristics of Torque, currents, speed and other if will able summary and comparison that's all.

    $108 (Avg Bid)
    $108 Avg Bid
    12 bids

    ...that compare them. Model of the motors, with the Magnetic field of motor Distribution of magnetic inductions. Characteristics of Torque, currents, speed and other if will able summary and comparison that's all. And at finally I need a report. I need characteristic, electric, mechanic, and other Models of the motors and comparison I need to be sure

    $117 (Avg Bid)
    $117 Avg Bid
    12 bids

    Gate and garage motor control. Motors control the gate and garage door. Both garage and gate have two limit switches(located at each end of travel) to trigger the DC motor to stop. 1. Add code to STOP the motors anywhere inbetween the travel to the two limit switches. if the serial key 'S' has been pressed 2. Add code for system to detect this

    $46 (Avg Bid)
    $46 Avg Bid
    9 bids

    Hello. We hace a raspberry pi with a C program that controlls motors. We need to find a C programmer to help us out adding some stuff to the code. we currently use DC motors with motor drivers.. we need to implement some encoders. we basically need you to review our code, and then if you find that you can do this we can interview you Thank you

    $640 (Avg Bid)
    $640 Avg Bid
    74 bids

    I need a PCB designer to design the circuit for my vending machine which would control 8 motors individually at set speeds.

    $196 (Avg Bid)
    $196 Avg Bid
    17 bids

    Within Ebay Motors listings, there is a java script table that appears that shows vehicle compatibility (Year, Make, Model, Trim, Engine Size, and Notes). We need the MOST EFFECTIVE scraper tool to do the compatibility list. The tool would need to do the follows: 1) Copy the compatibility list from existing listing to an excel sheet. 2) Extract that

    $289 (Avg Bid)
    $289 Avg Bid
    23 bids

    Autonomous lawnmower robot I'm very good at building and fabricating and welding but I don't know very much about programming and...straight RC mode let me know if you have any suggestions thank you very much what kind of information do you need from me let me know do I have to have some kind of encoders on my Motors what kind of Hardware will I need

    $136 (Avg Bid)
    $136 Avg Bid
    1 bids

    ...motor use programs for example motor analysis or other . For example: [login to view URL] I need basic operating characteristics. So that compare them. Model of the motors, with the Magnetic field of motor Distribution of magnetic inductions. characteristics of Torque, currents, speed and other if will able summary and comparison that's all

    $90 (Avg Bid)
    $90 Avg Bid
    12 bids

    ...And I am consulted to automate his business. First project I need help with is writing arduino code for a small xy table. I built the xy table. 50x50 cm Installed nema 17 motors and use a arduino uno with cnc shield v 3.0 and drivers. Searched the internet for how to code or copy and paste code for the Arduino. I spent a week now and am stuck. It

    $41 / hr (Avg Bid)
    $41 / hr Avg Bid
    1 bids